![]() I don’t consider any of these to be practical solutions, though - as far as I’m concerned, WEP no longer exists (too bad a lot of vendors still act like WPA doesn’t exist). I’m not inclined to blame the Netgear router, since a host of other wireless devices consistently have no difficulties connecting to it.ĭisabling encryption remedies the problem, but I also had better luck with WEP or swapping out for another router on hand (coincidentally, a Linksys WRT54GS). In this scenario, the camera rarely responded to pings, and on the few occasions it did, latencies were in the three to four second range. The camera supports WEP or WPA Personal (PSK), but attempts to use a WPA encrypted connection between the camera and my Netgear WPN824 router rendered the WVC200 inaccessible or resulted in a connection so flaky as to be essentially useless. Although the connection was always rock-solid via wired Ethernet, things got dicey when configuring the WVC200 to use the WLAN. Unfortunately, I had some serious issues getting the WVC200 to work properly over a wireless network. For obvious reasons, it’s preferable to assign the WVC200 a fixed IP address once you complete initial setup. From that point, I used the included Linksys utility to set up the basic IP and WLAN configuration, and went to a browser-based control panel for advanced settings and more comprehensive administrative control. SetupĪfter I plugged in the power and Ethernet cables, the WVC200 came to life and picked up an IP address from my router via DHCP. (If you’d prefer to use your own, there’s also a MIC IN jack provided.) You can set the camera into an included desktop stand, or wall-mount it instead. The camera mechanism is housed behind a clear plastic dome, below which is a condenser microphone with a maximum range of about 9 feet. The WVC200 can deliver video in either MPEG-4 or MJPEG (Motion JPEG) format, and supports three levels of resolution up to a maximum of 640 x 480. The LCD isn’t backlit, so it’s pretty much impossible to read from any position other than one inch directly in front of it, but chances are you won’t need to consult it very often anyway. The WVC200 features a small LCD screen that displays the device’s IP address plus whether the address is fixed or dynamically assigned. Owing to the space requirements of its PTZ motor, the WVC200 is somewhat larger than a regular webcam, though at about 9 inches tall (including the antenna) it’s still relatively compact. The PTZ here stands for Pan/Tilt/Zoom: the WVC200 can see much more than just what’s going on directly in front of it. But the downside of a typical webcam is a fixed position that (barring manual adjustment) gives it an extremely limited field of vision, and this makes it less than ideal for tasks such as surveillance, where camera mobility is extremely helpful, if not an outright requirement.Ī camera better suited for that sort of duty is the $299 Linksys Wireless-G PTZ Internet Camera (model WVC200), an 802.11g wireless network camera with built-in audio and motion-detection capabilities. The inexpensive and now ubiquitous webcam is a great way to keep in visual contact with far-flung friends, relatives and colleagues. I would appreciate any assistance and please feel free to be as detailed as possible when responding.Pros: Bargain price, pan/tilt controls, motion detection featureĬons: Serious connectivity problems with WPA-encrypted connections unrealistic color reproduction scant documentation browser video plug-in doesn’t work with Firefox. If the above is correct, how would I set the second router to 192.168.1.2 given that the Wired router is already using 192.168.1.1 which is the default for the Wireless as well? Also what port on the Wireless router should I use to connect to what switch port on the Wired router? However the post I saw was referring to connecting 2 Wireless routers and although the concept is similar I am looking for some guidance. I have seen a post on another site that indicate that I would need to change the IP address of the Wireless router to 192.168.1.2, turn off DHCP, and then connect a cable between the Wireless router and the Wired router. I do not want to remove my BEFSR41 router as my primary gateway. ![]() My question is how would I go about this. I would like to use the WKPC54G Wireless router as an access point only. ![]() I have recently purchased the Linksys WKPC54G Wireless-G Network Kit for Notebooks that includes a WRK54G Wireless G router and WPC54G Wireless-G Notebook Adapter. I currently have a Linksys BEFSR41 EtherFast Cable/DSL Router with 4-Port Switch that acts as my gateway. ![]()
0 Comments
Leave a Reply. |